# Firmware release notes

What changed in each version of the site controllers EVSE-SC-01 and EVSE-SC-02 and the charge controller EVSE-C-3x32A, newest first. Updates are installed over the air: fixes and security updates for every site controller, new features with a subscription.

Canonical: https://edgetech.eu/docs/firmware  
Updated: 2026-11-05

Release notes per version of the site controller and charge controller firmware, newest first. Updates are installed over the air: fixes and security updates reach every site controller, new features need a subscription. Each version number is the one the site controller reports in the app.

Up to version 3.0 (EVSE-SC-01) and 0.3 (EVSE-SC-02), a site controller release also carried new firmware for the charge controllers, which the site controller installs on them over the Modbus cable. Since 2026 the charge controller firmware is released separately; the current version is 2.10.17.

## Site controller EVSE-SC-01 (CT clamps)

### 4.2.3 — November 2026
- A hardware watchdog: if the site controller ever locks up (seen during a software update over a very poor internet connection), it restarts by itself within about a minute instead of staying offline until someone switches it off and on.
- After an outage of the EdgeTech platform, the site controllers no longer all restart at the same moment. A site controller that is charging a car never restarts for this reason, and it only restarts when the problem is local.
- After a software update the LED could keep blinking cyan ("connecting") although the site controller was online; it now breathes cyan when connected.
- Small robustness fixes.

### 4.2 — October 2026
- Connecting the site controller to a new WiFi network with the app now works without a factory reset. Setup mode restarts a site controller that was already connected; see the manual, section 8.
- Better protection against an unstable power supply: when the supply voltage dips, the site controller restarts cleanly.
- More detail in the status for support: why a charge point gets less current than its maximum, how long each charge controller has been running, and whether it restarted.

### 4.1 — June 2026
- A short interruption of the connection to the platform no longer interrupts a charging session.
- More reliable recovery after a WiFi or internet outage, and no unnecessary restarts on WiFi networks with a weak or unusual signal.
- Fixed: after about 25 days of continuous operation, the site controller could lose contact with its charge controllers, so charging could no longer be started or stopped remotely.
- The maximum site current can now be set from 6 A (was 16 A), and every settings change is confirmed back to the app.
- More reliable power measurement.
- Charge controllers that are updated at start-up, or that report a hardware fault, are now recognised and reported automatically, without a restart.

### 4.0 — April 2026
- Connects to the new EdgeTech platform.
- Charging continues during a WiFi outage, and the site controller reconnects by itself when the network returns, without restarting.
- After a power cut, charging resumes immediately, even before WiFi is back.
- The LED shows whether the site controller is connected to the platform.
- Regular status reports, so support can see that an idle site controller is healthy.
- Fixed: setup mode for a new WiFi network did not always start.

### 3.0 — April 2025
- Better handling of cars that go into sleep mode (IEC 61851-23 Edition 2).
- The charge point type can be set per charger.
- New charge controller firmware (2.10.17).

### 2.8 — September 2023
- Live current data in the app (one minute at a time) over the local network.
- More information about the site controller and the position of each charger at start-up, for faster support.
- Better handling of cars that go into sleep mode.
- New charge controller firmware with stability improvements.

### 2.6 — August 2022
- Improved charging algorithm: smoother increase of the charge current and better use of the minimum charge current.
- The maximum current for the whole site, and for all charge points together, can be set.
- Fixed: on sites with many solar panels the direction of the current was not always detected correctly.
- Better power reading and more reliable software updates.

### 2.5 — June 2022
- Improved phase detection.
- The user can accept or decline a software update.

### 2.4 — March 2022
- The minimum charge current can be set.
- Better sharing of the available current when several chargers charge at the same time.
- The total kWh per charge point is stored in the site controller itself.
- Clearer warning when a car draws more current than offered.

### 2.3 — January 2022
- Messages for errors such as board faults, communication errors, a charge controller running hot or a failed charge controller update.
- Fixed: "allow charging" did not work correctly with two chargers.
- Factory reset now works per charger, and a replaced charger is picked up correctly.
- Charging sessions are kept and merged when the site controller is temporarily offline.

### 2.2 — March 2021 (first production batch)
- First production release.
- Priorities and a charging queue for sites with several chargers.
- Plug & charge can be switched on and off; the energy per charging session is recorded.
- Other types of CT clamps can be used.
- Charge controller firmware can be updated remotely; factory reset with the button.
- Improved WiFi setup.

## Site controller EVSE-SC-02 (P1 port of the smart meter)

### 1.1.4 — November 2026
- The same fixes as 4.2.3 for the EVSE-SC-01: a hardware watchdog, no mass restarts after a platform outage, and the LED fix.
- A malformed setting from the platform can no longer make the site controller restart.
- If the smart meter sends only unreadable data (for example through a faulty P1 cable or a P1 splitter), or nothing at all, the site controller now recognises this, pauses charging safely and reports the cause, so support sees it straight away.

### 1.1 — October 2026
- Connecting the site controller to a new WiFi network with the app now works without a factory reset. Setup mode restarts a site controller that was already connected; see the manual, section 8.
- More detail in the status for support: why a charge point gets less current than its maximum (including charging on solar surplus), how long each charge controller has been running, and whether it restarted.

### 1.0 — June 2026
- Connects to the new EdgeTech platform.
- Safer when the smart meter stops sending readings: charging pauses until readings return, so the main fuse is never at risk.
- Setting up WiFi with the app works reliably again, and new chargers appear in the app right after commissioning, without a restart.
- A short interruption of the connection to the platform no longer interrupts a charging session, and the site controller recovers by itself after a WiFi or internet outage.
- Better protection against an unstable power supply. The maximum site current can now be set from 6 A, and every settings change is confirmed back to the app.
- The LEDs now correctly show power, network, platform connection and communication with the charge controllers.
- Fixed: power readings could miss their last digit.

### 0.3 — September 2025
- Support for Belgian smart meters.

### 0.2 — October 2024
- Charging on solar surplus: solar production is measured through the smart meter and used for charging.
- More settings and status information in the app, including the temperature and maximum current of each charge point.
- Charging sessions are kept across a restart of the site controller.
- A list of known WiFi networks, for easier reconnection.
- The charge point type can be set; new charge controller firmware with better handling of cars that go into sleep mode.

### 0.1 — September 2024
- First version in the field.
- Fixed: the energy per charging session was not always read correctly.

## Charge controller EVSE-C-3x32A

The firmware of the charge controller itself. Only the versions that went out to chargers in the field are listed; each one includes the changes of the test versions before it. Until 2026 these came with a site controller release (see above).

### 2.10.17 — April 2025
- At plug-in the charger first gives the car a calm, steady signal for a few seconds before it offers current. Cars that are slow to wake up start charging more reliably.
- Better handling of the cable disconnect signal, so the charger and the car agree reliably when a session ends.

### 2.10.14 — September 2024
- More reliable start-up of the charger after power-on.
- Better support for firmware updates over the air.

### 2.10.7 — June 2024
- Fixed: ending a session with certain car models.

### 2.10.6 — May 2024
- New "charger not available" signal to the car, used to pause a car or wake it up correctly.

### 2.10.4 — February 2024
- Support for cable-lock drivers.
- The charger can now actively signal a disconnect to the car.

### 2.10.1 — February 2023
- Faster DC leakage detection: 7 ms reaction time.
- More robust communication with the site controller.

### 2.9.17 — December 2022
- More accurate power and energy measurement, including the direction of power.
- More robust communication with the site controller.

### 2.9.15 — September 2022
- Improved control of the neutral relay; the charger now detects a relay that fails to close.

### 2.9.14 — June 2022
- Monitoring of the quality of the earth (PE) connection.

### 2.9.12 — April 2022
- Total kWh and kWh per charging session, per phase, stored in the charger itself.
- More reliable energy measurement: the measurement chip recovers automatically, and energy totals are stored safely.
- Better handling of the charging states.
- Cleaner power readings: very small currents are ignored.

### 2.6.1 — July 2021
- New LED colour scheme.
- New board revision with earth and neutral monitoring.
- Fixed: the power reading in single-phase mode.

### 2.4.1 — February 2021
- Fixed: the voltage reading.

### 2.3.1 — December 2020 (first production batch, March 2021)
- Fixed: the charging state when no current is offered.
